Clippers and Blades

Big Admin May 5, 2018 31






I just wanted to show you what kind of clippers I use and a little bit about blades. I hope this helps some of you. The clippers can run about $150.00 and the blades start at about $20 and…

source


31 Comments »

  1. Stacer86 July 2, 2013 at 9:16 pm - Reply

    Love your videos, very helpful, thanks so much for posting them!

  2. starlite556 July 22, 2013 at 2:30 am - Reply

    I would like to know if the oil used on the clipper is toxic to a dog and also do you clip a dog before or after a bath. And also the blade on my Andis clipper gets very hot with in about a minute is this normal? Thank you.

  3. spanielmom93 July 22, 2013 at 2:17 pm - Reply

    The oil used on the clipper comes with the clipper and the clippers are made for dogs so no it should not be toxic to the dog. I would keep it out of their reach and also they could have an allergic reaction I'm sure… just try to wipe all the excess off before using the blade again. I will do both clip before and after bath usually. It is normal for a blade to get hot, but within a minute is telling me maybe you need to replace the "blade drive" on your clipper.

  4. stephanie cottrell September 17, 2013 at 5:42 pm - Reply

    Can you please tell me why my clippers are getting hot?

  5. stephanie cottrell September 17, 2013 at 5:46 pm - Reply

    You rock! A great video
    Steph

  6. Derek Hartmann September 26, 2013 at 3:59 pm - Reply

    The blade oil that comes with the purchase of clippers is just your standard mineral oil. The problem with this oil is that it is too light and will easily run off the blade and it does not handle the amount of load that builds on the clipper. The Speedy Blade Oil addresses these issues.

  7. Derek Hartmann September 26, 2013 at 4:05 pm - Reply

    If your clippers are running hot, you have a electrical issue. It could be the armature (motor), switch, or you could have a crack in the magnetic field that houses your armature. If your blades are getting hot quickly, the blade drive could be making contact to the comb section which will cause your blades to heat up quickly or you may just need to apply more oil to your blades.

  8. Melissa P December 1, 2013 at 4:33 am - Reply

    i absolutely LOVE your videos!!!  you are amazing for sharing all your knowledge with us!

  9. Kelli McCully January 18, 2014 at 11:43 pm - Reply

    Thank you for taking the time to share your video!  I have been using combs but I have some blades and didn't know how to use them, but I think next time I clip my shih tzu I will try the blades instead as the combs pull his hair.

  10. jjintheflesh February 9, 2014 at 2:46 am - Reply

    This is awesome! Thanks for the info learned a lot!

  11. Linda Schmidt February 22, 2014 at 3:57 am - Reply

    Hi, maybe I missed it, but did you say what size blade you use to get the 'teddy bear' look on the body?  I always thought it had something to do with the 'clip on combs', but it looks more like you use a certain type of bade.  I have a shihtzu.  Thanks for replying.

  12. Joyce Robertson March 2, 2014 at 2:07 am - Reply

    Great info and explanations for each blade – exactly what I needed!

  13. Katie Mac July 14, 2014 at 3:10 am - Reply

    Excellent video. Thank you.

  14. elle oh elle January 26, 2015 at 6:24 pm - Reply

    GREAT!!

  15. acer.b March 26, 2015 at 3:36 pm - Reply

    Thank you so much for the informative video! I want to try to groom my dog (a Westie) myself instead of taking him to a professional since our last experience was unfortunately a bad one. I have a question: Should I get the #4 or the #4FC  if my dog's coat is a little rough? He hasn't been groomed in over a year. I'm just a bit confused – does the "fine cut" refer to how I want the dog's coat to be afterwards? Or if the dog's hair is fine/thin to begin with?

  16. Lenetta Carnes May 26, 2015 at 7:14 pm - Reply

    Thanks so much for showing the different blades. Just getting ready to do my first cuts on my dogs. I just purchase the and is agc2 pro clip clippers. It came with a 10 blade and I also got a 5fc blade. This really helped me to understand what the different blades are for. 🙂

  17. Debra Adair December 19, 2015 at 2:49 pm - Reply

    This is so helpful! After burning out numerous regular clippers, I bought Andis.

  18. Hai Nguyen January 3, 2016 at 3:11 am - Reply

    Thanks, your is the most compete about blades. I have a JIt shu with very matted hair, I bought several cheap Wahl clippers , after few times they stop working. I wonder whether because I do not have a correct type of blades. Is it correct?
    How do you sharpen your blades if they don't cut ?

  19. Rharesh Shan February 16, 2016 at 4:10 am - Reply

    what blade is suitable for stomach area because female dog's have nipples please let me know tq

  20. Michelle Mattson February 22, 2016 at 10:25 pm - Reply

    Thanks. Very helpful but I'd like more examples of which dogs you use the last couple on. Still a thumbs up

  21. Queen Happy April 29, 2016 at 8:00 pm - Reply

    what about #30

  22. U TELEVEN July 16, 2016 at 4:07 am - Reply

    thank you!

  23. robert S October 22, 2016 at 4:52 am - Reply

    that last blade could you use that for feet.

  24. robert S October 22, 2016 at 4:59 am - Reply

    the bottom of the feet is what I meant I am using a Andis AGC clipper with a number 10 blade I have decided to groom my dog myself instead of paying 100.00 to get him groomed at PetSmart every three to four months he is a poodle/havanese  mix  but my blade gets really hot after 6 minutes so I have to stop and let it cool off so I am thinking about getting a ceramic blade I was told they stay cooler longer is that true.

  25. Rainy Tedandeffi December 14, 2016 at 11:11 am - Reply

    This video has been extremely helpful to me as it's very hard to get groomers to share their info. I'd like to start going my lhasa apsos myself and i'm totally baffled by the blades and all the numbers on them too. What blades would you recommend i get i don't like them totally scalped but i like them short and neat.

  26. Yuva nesh January 24, 2017 at 5:06 am - Reply

    thanks for sharing the info ma'am I appreciate it

  27. Peter Cobalt April 24, 2017 at 11:27 am - Reply

    thank you so much that's helped a lot 🐶

  28. Tugboat September 27, 2017 at 4:45 am - Reply

    Great review of blades. Our westy has bad skin, when not on antibiotics. Would a 4f be better then her normal 7f? We cut our cavalier with 7f. Thank you

  29. Dora Silva January 11, 2018 at 6:22 pm - Reply

    Thx for your help, I sure learned a lot from you today, I am an apprentice of dog groomer for my own dogs, I am loving it!!! 😀 Thx ahgain!!

  30. Tim Kuhner January 24, 2018 at 12:04 am - Reply

    Thank you!

  31. Ms. Horsetrainer April 18, 2018 at 9:38 pm - Reply

    video to dark can't see what you are trying to show us beginners. Moving to fast through the blades.

Leave A Response »

Skip to toolbar